Adjusting Stream Rate - Developer Docs

Overview

joint_states broadcasts at about 1 kHz by default, which is more than most applications need. set_rate() asks the firmware to push at a rate you choose, cutting network and CPU cost. The rate belongs to the stream, not to a subscription handle: the setting applies to every subscriber of that stream, and it returns to the device default once the last subscription closes or the device reconnects. Matching examples: examples/python/wuji_hand_2/4.set_stream_rate.py and examples/c/wuji_hand_2/4_set_stream_rate.c. For the list of adjustable streams and their API definitions, see SDK Reference. This page covers only how to run it and what the measurements show.

This feature has a firmware requirement. Wuji Hand 2 needs firmware v2.3.0 or later, and devices below that raise on the call. The device verified here runs older firmware, so the success path is described from the release notes and the failure path is measured.

Prerequisites

Hardware

Item	Requirement
Wuji Hand 2	1, firmware v2.3.0 or later
Connection	Ethernet

Software

Item	Requirement
Wuji SDK	v2026.8.17 or later, which introduced `Subscription.set_rate()`
Python	3.10 or later
C toolchain	CMake 3.16 or later, plus the extracted SDK package

Adjustable and Derived Streams

Device	Adjustable streams
Wuji Hand 2	`joint_states`, `joint_diagnostics`, `imu`, `fingertip/{thumb,index,middle,ring,pinky}/data`
Wuji Glove	`emf_poses`, `tactile`, `tactile_zones`, `imu_raw/*`

Derived streams reject set_rate. hand_joint_angles, hand_skeleton, tip_poses, and imu_data/* are computed from source streams and follow their rate, so calling it on them directly is rejected. joint_states and joint_diagnostics share one device stream. Adjusting the rate through either subscription changes both.

Data Flow

The request is quantized to a rate the device supports, and the return value is what actually took effect. Don’t assume it equals the request.

Runtime Handling

Branch point	Behavior	What to do
Firmware doesn’t support it	Raises `WujiException: Unsupported operation: device 'SN' runs firmware without rate control`	Upgrade the firmware to v2.3.0 or later
Called on a derived stream	Rejected	Adjust its source stream instead
Unsupported stream on the C side	Returns `WUJI_STATUS_ERR_UNSUPPORTED` (-8) and sends no request to the device	Check the return code
Passing 0	Restores the device default rate	Returns the default value
Last subscription closes	The rate returns to the device default automatically	Keep the handle open to keep the setting
Device reconnects	The rate returns to the device default	Set it again after reconnecting

Integration Steps

Python
C

import asyncio
from wuji_sdk import DeviceType, SdkManager

async def main():
    manager = SdkManager.instance()
    hands = [d for d in manager.scan() if d.device_type == DeviceType.WujiHand2]
    sub = None
    try:
        hand = manager.connect(sn=hands[0].sn, device_name="hand")

        # 1. Get a subscription handle. The rate lasts while the handle lives
        sub = hand.joint_states().subscribe()

        # 2. Request a lower rate. The return value is what the device applied
        actual = sub.set_rate(100)
        print(f"requested 100 Hz, device applied {actual} Hz")

        for _ in range(5):
            frame = await sub.recv_async()
            print(f"frame at {actual} Hz: {len(frame.joints)} joints")

        # 3. Pass 0 to restore the device default
        print(f"restored to default: {sub.set_rate(0)} Hz")
    finally:
        if sub is not None:
            sub.close()
        manager.disconnect_all()

asyncio.run(main())

#include "wuji_sdk.h"

/* 1. Subscribe */
struct WujiSub *sub = NULL;
wuji_hand_2_subscribe_joint_states(dev, on_frame, &ctx, &sub);

/* 2. Adjust the rate. Any subscription handle can do this */
uint32_t actual = 0;
WujiStatus st = wuji_sub_set_rate(sub, 100, &actual);
if (st == WUJI_STATUS_ERR_UNSUPPORTED) {
    /* -8: this stream has no rate control, and no request went to the device */
} else if (st == WUJI_STATUS_OK) {
    printf("requested 100 Hz, device applied %u Hz\n", actual);
}

/* 3. Pass 0 to restore the default */
wuji_sub_set_rate(sub, 0, &actual);

wuji_sub_close(sub);

The rate restores itself once the handle closes, so keep the handle open to keep the setting in effect.

Running It

Python
C

python examples/python/wuji_hand_2/4.set_stream_rate.py

./build/hand2/4_set_stream_rate

With supporting firmware, output looks like this:

Connected: WH2KA00XXXXXXXXX
joint_states: requested 100 Hz, device applied 100 Hz
joint_states frame at 100 Hz: 20 joints
...
restored to the device default: 1000 Hz

Measured Behavior Without Firmware Support

Calling this on a device below firmware v2.3.0 raises immediately:

wuji_sdk.WujiException: Unsupported operation: device 'WH2KA00XXXXXXXXX' runs firmware without rate control

The exception comes from the set_rate() call site and leaves the subscription untouched — it keeps working, simply at the device default rate. On that device, joint_states measured about 1088 Hz by default. The most direct way to test support is to call set_rate() once and see whether it raises. The SDK has no separate capability query.

Adapting It

Picking a Rate

Requests are quantized. To confirm what took effect, read the return value of set_rate(), or count frames over a fixed interval after subscribing.

Effect on Other Subscribers

The rate belongs to the stream. With several subscribers on one stream, a change by any of them reaches all of them. That matters most when processes share a device, where one process lowering the rate can undercut another’s timing.

Lowering joint_states Also Lowers joint_diagnostics

They share one device stream, so lowering only one of them isn’t possible.

When to Restore

When you don’t need an explicit restore, just close the handle and the rate returns to the device default. Passing 0 explicitly suits continuing to receive at the default rate on the same handle.

Subscribing With Callbacks: how subscriptions are created and live
Subscribing Asynchronously: using recv_async() alongside a lowered rate
Wuji Glove Adjusting Stream Rate: the same capability on the glove, requiring firmware v0.11.4 or later

​Overview

​Prerequisites

​Hardware

​Software

​Adjustable and Derived Streams

​Data Flow

​Runtime Handling

​Integration Steps

​Running It

​Measured Behavior Without Firmware Support

​Adapting It

​Picking a Rate

​Effect on Other Subscribers

​Lowering joint_states Also Lowers joint_diagnostics

​When to Restore

​Related

Overview

Prerequisites

Hardware

Software

Adjustable and Derived Streams

Data Flow

Runtime Handling

Integration Steps

Running It

Measured Behavior Without Firmware Support

Adapting It

Picking a Rate

Effect on Other Subscribers

Lowering joint_states Also Lowers joint_diagnostics

When to Restore

Related